Built for Mud, Dust, and Vibration
Geotab GO Rugged · Sealed off-road tracker
Rugged Design
Locking connectors take pressure washing, mud, weather, and vibration.
Mounts on machines with nowhere to plug in, stays put, and reads faults and run-time from the equipment.
Weatherproof wiring, matched to each machine before install.
Heavy equipment and trailers beside the rest of your fleet, with an alert and the path when one moves off-hours.
Also built in: GPS + GLONASS, accident detection, and auto-calibration on power-up.















Why GO Rugged
Utilization, service hours, and site time share one record that follows each machine.

Real engine hours land automatically, so service intervals and utilization run on the machine's own count.
See which machines earn and which ones sit, before you rent another one.
Yards, jobs, and everything in between, with geofence alerts on movement.
Uptime & Health
GO Rugged turns fault codes and engine hours into planned service, not a machine stranded on site.

Idle and Fuel Costs
Idle burn, fuel, and hours from every GO Rugged machine land in the same reports as your trucks.
Idle time and the fuel it burns show for every machine, in the same reports as your trucks.
Real engine hours show which machines earn and which ones sit before you rent another one.
GO Rugged machines and on-road trucks share the same fuel and idling reports.
Heavy Equipment
Haul trucks, loaders, dozers, and excavators, all reporting hours, faults, and position live.
Each machine's maintenance schedule runs on its real engine hours, with its due status on one list.
Faults come straight from the machine, so the shop triages from the office.
Off-hours moves raise an alert, and location history shows the path.

Match the Hardware
Match each asset to the device built for it, and watch them all report to the same map.
Trucks and pickups, installed Plug-N-Play on vehicle power. See vehicle tracking.
Excavators, loaders, and dozers, sealed to IP68 and IP69K, on 12V and 24V equipment.
Trailers, containers, and gensets, with no power needed and a battery that lasts up to 10 years. See asset tracking.
GO Rugged Add-Ons
GO Rugged does not stop at location: satellite, panic buttons, and temperature all plug into it.
A satellite add-on keeps the machine reporting past the edge of cellular.
A physical panic button for the operator working alone.
A rugged temperature add-on (IOX-COLD) puts reefer trailers on the map, with readings for up to 3 zones.
One device family, one platform. Add-ons bolt on, so oil and gas fleets run GO Rugged past the last bar of signal.
Camera Add-On
A camera plugs into the tracker already on the machine, with nothing new to log into.
The GO Focus Pro takes auxiliary cameras for rear and side views on trucks and heavy equipment.
Cameras bolt on like the other add-ons, so video joins the platform your machines already report to.
Machines with cameras stay on the same map and in the same reports as your trucks and trailers.

Where It Works
Standard trackers fail in these environments. GO Rugged is sealed for them and reports through them.
Excavators, dozers, loaders, haul trucks and crushers, from the job site to the pit.
Pump trucks and generators on remote pads.
Tractors, sprayers, and harvesters in the field.
Backhoes, trenchers, gensets, graders, sweepers, and loaders, from the territory to DOT yards.
Equipment Activity
GO Rugged counts dump cycles and PTO hours, and alerts when a parked machine moves.
Each raise of the bed is counted by the tracker, not kept on a tally sheet.
PTO run time is recorded on its own, beside engine hours and location.
Satellite, a panic button, and temperature sensors plug into the same GO Rugged.
Questions
It is a sealed, IP68 and IP69K rated device built for off-road equipment and harsh sites where a standard device would not survive.
Yes. Engine hours and usage feed maintenance schedules so heavy assets get serviced on real use.
Yes. GO Rugged reports onto the same map and into the same reports as the rest of your fleet, trucks and trailers included.
No. It is rated for exactly that: high-pressure, high-temperature washdowns. Wash the machine like you mean it.
Different device, same map: non-powered assets get a battery-powered GO Anywhere, on one screen with GO Rugged.
Yes, two ways: the device stores data until coverage returns, and a satellite add-on carries critical data.
Yes. GO Rugged installs on 12V and 24V equipment, and we confirm the right weatherproof wiring before it ships.
“We are tracking a little over three-thousand assets; from pickups to off-road equipment, trailers, generators, compressors. Each type requires different reporting metrics. All our reports, dashboards and live alerts are personalized and formatted according to asset type and each of our users’ independent needs. This has been a game changer!”KS Energy, New Berlin, WI
Keep exploring
Related reading: Fleet Right-Sizing: Find the Units That Sit Before You Buy Another
Tell us what you run and we will ship a free demo device configured for your machines, ready to report.